|
Makita 784832-A Quad-Driver 13 Piece Pre-Drill, Drive and Countersink Set | 
| Brand: Makita
Category: Home Improvement
List Price: $51.40
Buy New: $27.49
You Save: $23.91 (47%)
Rating:  10 reviews
Sales Rank: 3331
Media: Tools & Hardware
Shipping Weight (lbs): 0.8
Dimensions (in): 11.6 x 6.8 x 1.3
MPN: 784832-A
Model: 784832-A
UPC: 088381925457
EAN: 0088381925457
ASIN: B0000224F5
Availability: Usually ships in 1-2 business days
| |
| Features:
| • | Do four jobs with one drill | | • | Change from a drill and coutersink to power screwdriver | | • | No need to remove the driver from your power tool | | • | Includes: quad driver shaft, built in hex key, #6, #8, #10, #12, countersink driver | | • | Case included |
|
| Accessories:
|
| Similar Items:
|
| Editorial Reviews:
Product Description
Includes Quad-Driver shaft with built-in hex key, No. 6, No. 8, No. 10, and No. 12 reversing countersink/driver, (4) No. 2 Phillips inserts bits and four extra drill bits, and case.
|
| Customer Reviews: Read 5 more reviews...
 Convenient and reasonably well made; June 28, 2008
1 out of 1 found this review helpful
I've been using this set in my workshop, mostly for drilling & sinking screws for drawer slides, hinges, etc. Like any other tool it needs to be handled with a certain amount of care and as other reviews note, the stud that mounts in the drill chuck is aluminum, not steel. I can imagine that some of the less happy reviewers were using it at a job site rather than in a workshop.
It's very convenient when you want to drill and countersink in one motion, and then sink the screw. You don't have to change from a more typical drill/countersink bit to a separate crewdriver bit. Just twist the collar on the stud that mounts in your drill chuck, and reverse the drill bit, and you have the right screwdriver bit for the size screw you've drilled for.
It's most useful when you want to sink the screw right after you've drilled and then go on to drill the next hole, etc. It wouldn't add that much efficiency if you're drilling a lot of holes one after the other, and then going back to set all the screws.
The best on the market, even with it's drawbacks May 18, 2008
2 out of 2 found this review helpful
I've been using this driver set since about 1997. I'm on my third set, which I just got a few weeks ago. When my second set wore out, I tried every other brand I could find, and finally went back to this one, even though it's not easy to find in stores and has several drawbacks.
The best: drill and screw with one bit, narrowest lock band for close drilling, positive locking, allen wrench in back end (might be the best feature).
The worst: the main shaft is a bit undersized and can get out of true if dropped more easily than others, allen screws wear out, hard to find new kits.
In practice, I have different bits (square, flat, phillips #'s 1,2 and 3) already installed in different holders with the most likely drill size (mostly #'s 6 and 8). That way, I never have to switch the driver tip on the job unless I break one, or it wears out (it happens, and it's a normal wear item, won't last forever), I just grab a different holder and it's ready to go.
If you're serious about drilling and driving, you need both in one holder. Other brands wear out quicker (I test them working 8 hour days, 5 days a week in a Milwaukee 18v lithium drill: I use it for kitchen and bath remodels and concrete counter mold making; I'm using this kit as much as anyone could, and using it HARD).
The allen screws that hold the bits do wear out, prepare for it. When one breaks, I steal one from an underused size holder and pick up a new one next time I go to the hardware store.
I've tried them all, nothing compares in functionality, and the others require even more careful maintenance to keep them working.
 Terrible Quality December 4, 2006
5 out of 6 found this review helpful
This kit was purchased to replace an older Makita bit that I had been using frequently for almost 10 years before I lost it. This new one broke where the screw tip inserts into the bit the very first time I used it. Very cheap, very poor quality.
poor quality made in china September 14, 2006
5 out of 6 found this review helpful
The bits either get jammed or fall out of the driver shaft, the locking ring falls off, the crews that hold the bits fall off and could not be secured. The overall construction is poor. The parts are made from aluminum and not the stainless steel. One bit broke in the second screw. I called Amazon at 866-660-8114 before ordering. The rep said that all Makita tools and accessories are made in either the US or Japan. Not true! This set was made in China. I bought this set to be used with the Makita 14.4 V impact driver, which also made in China. I am returning this set.
 Easy to use March 27, 2006
3 out of 3 found this review helpful
I've been using this set for 6 or 7 years now, on a variety of woodworking and home improvement projects. Beyond tightening up the allen screws every now and then, and replacing bits and phillips heads, this product has exceeded my expectations. To be brief, it's sturdy, compact, works as advertised, and is easy to use. Flipping from drilling to screwing is a snap--really, just slide the snap ring up, rotate the bit, snap the ring down and you're ready to go.
The drill bits are a little specialized, since they have a flat spot to set the allen screw against so it won't spin in place. I found a local distributor who was more than happy to sell me a couple sets of three bits in the sizes I wear out fastest (#6 and #8).
Go ahead and buy this product, you won't be disappointed.
|
|
|
Not sure you are seeing the best price? Compare at PriceRunner
powered by full speed | |
